Breaking

E-Guru Sumit         Blog         Youtube

Post Top Ad

COMPUTER TROUBLE SHOOTING

Computer Trouble Shooting

 

        First Page         

Troubleshooting in computer and their others peripherals is a complex process. There can be many reasons for one fault in this by identifying these reasons, this process becomes much easier and the problem can be easily removed. Some things to keep in mind while shooting trouble.

1)    Do not handle any device rough.

2)   When a device is not opened or inserted, it should not be forced, but to find out the reason.

3)   When opening the device or cover, each screw received should be kept in one place.

4)  Each of screw should be placed in its place when turning of the system or other device.

5)  Before opening any system, this device should be thoroughly inspected.

6)  There are fewer screw and more clips in computer, printer, device, so the technique of opening them should be looked at first.

7)   Do not open or close any device with power.

8)   The device must discharge itself by touching the wall etc., before touching the electronic circuit.

9)  The device should not be operate with a screw driver or hand in the ON condition.

10) While replacing any components, the device of old value should be mixed together.

11) Sophisticated devices should not be touched repeatedly by hand.

 

Faults can be of two types, solid and intermittent.

Solid fault: this type of fault is called a permanent fault. Any work gets completed by them.

Intermittent fault: these types of fault come intermittently in the system. Some times the system start  working fine and sometime is faulty.

Hardware fault: the reason for system failure is some hardware device like RAM, HDD, FDD, interface card, SMPS etc., in this case, the faulty device needs to be taken.

Software fault: if the reason for the system not working now is software, then there is no need to open the system but it can be corrected only by software tools and diagnostic software. Computer trouble shooting is divided into four main parts. At this time, on the basis of systematic trouble shooting, any system defect can be detected and rectified. It following:

 1)   Symptoms observation

 2)   Symptoms analysis

 3)    Fault diagnosis

 4)   Fault rectification

Symptoms observation: To rectify a system failure, one should first look carefully at the symptom caused by the fault. Most fault are detected from the outside of the system itself. it should not jump to any conclusion without observation.

Symptom analysis: the system symptoms should observed or analyzed to see if the problem could be from any section of the system. the problem is hardware by doing system analysis from software`s memory device or power supply, we can start the process of repair in the right section.

Fault diagnosis: the cause and department of the fault can be ascertained by one time symptom observation. The process of locating and repairing the faulty device should begin. There should be absolutely no rough handling while making fault diagnosis.

Fault rectification: after the diagnosis, if you are replacing the faulty device, then the matching of the device must be kept in mind and the value and capacity of the new device should be combined. A computer is such a device that it dose not work just by replacing the new divide, but it also needs to be configured by the bios software. After replacing the device, meet these requirements as well.



Next Topic Is :-Matching  And  Mismatchig Of Ram :- Page(2)  Comming Soon


कंप्यूटर समस्या की शूटिंग                          

कंप्यूटर और उनके अन्य बाह्य उपकरणों में समस्या निवारण एक जटिल प्रक्रिया है। इसमें एक दोष के कई कारण हो सकते हैं इन कारणों की पहचान करने से यह प्रक्रिया काफी आसान हो जाती है और समस्या को आसानी से दूर किया जा सकता है। शूटिंग में परेशानी होने पर कुछ बातों का ध्यान रखें।                   

                        

1) किसी भी उपकरण को खुरदुरे तरीके से न संभालें।

 2) जब कोई उपकरण खोला या डाला नहीं जाता है, तो उसे मजबूर नहीं किया जाना चाहिए, बल्कि कारण का पता लगाना चाहिए।

 3) डिवाइस या कवर खोलते समय, प्राप्त प्रत्येक स्क्रू को एक ही स्थान पर रखा जाना चाहिए।

 4) सिस्टम या अन्य डिवाइस को घुमाते समय प्रत्येक स्क्रू को उसके स्थान पर रखा जाना चाहिए।

 5) किसी भी सिस्टम को खोलने से पहले इस डिवाइस का अच्छी तरह से निरीक्षण कर लेना चाहिए।

 6) कंप्यूटर, प्रिंटर, डिवाइस में स्क्रू कम और क्लिप ज्यादा होते हैं, इसलिए उन्हें खोलने की तकनीक पहले देखनी चाहिए।

7) किसी भी उपकरण को शक्ति के साथ न खोलें और न ही बंद करें।

8) इलेक्ट्रॉनिक सर्किट को छूने से पहले डिवाइस को दीवार आदि को छूकर खुद को डिस्चार्ज करना चाहिए। 

 9) डिवाइस को चालू स्थिति में स्क्रू ड्राइवर या हाथ से संचालित नहीं किया जाना चाहिए।

10) किसी भी पुर्जे को बदलते समय पुराने मूल्य के उपकरण को आपस में मिला देना चाहिए।

 11) परिष्कृत उपकरणों को बार-बार हाथ से नहीं छूना चाहिए।   


दोष दो प्रकार के हो सकते हैं, ठोस और रुक-रुक कर।

ठोस दोष: इस प्रकार के दोष को स्थायी दोष कहते हैं। इनके द्वारा कोई भी कार्य पूर्ण होता है।

इंटरमिटेंट फॉल्ट: इस प्रकार के फॉल्ट सिस्टम में रुक-रुक कर आते हैं। कई बार सिस्टम ठीक से काम करना शुरू कर देता है और कभी-कभी खराब हो जाता है।

हार्डवेयर फॉल्ट: सिस्टम फेल होने का कारण कुछ हार्डवेयर डिवाइस जैसे रैम, एचडीडी, एफडीडी, इंटरफेस कार्ड, एसएमपीएस आदि हैं, ऐसे में दोषपूर्ण डिवाइस को लेने की जरूरत होती है।   

सॉफ्टवेयर की खराबी: अगर सिस्टम के अभी काम न करने का कारण सॉफ्टवेयर है, तो सिस्टम को खोलने की कोई जरूरत नहीं है लेकिन इसे सॉफ्टवेयर टूल्स और डायग्नोस्टिक सॉफ्टवेयर द्वारा ही ठीक किया जा सकता है। कंप्यूटर ट्रबल शूटिंग को चार मुख्य भागों में बांटा गया है। इस समय, व्यवस्थित समस्या निवारण के आधार पर, किसी भी सिस्टम दोष का पता लगाया जा सकता है और उसे ठीक किया जा सकता है। यह निम्नलिखित है:

1) लक्षण अवलोकन

2) लक्षण विश्लेषण

3) दोष निदान

4) दोष सुधार    


लक्षण अवलोकन: किसी प्रणाली की विफलता को ठीक करने के लिए, सबसे पहले दोष के कारण होने वाले लक्षणों को ध्यान से देखना चाहिए। अधिकांश खराबी का पता सिस्टम के बाहर से ही लगाया जाता है। इसे बिना अवलोकन के किसी निष्कर्ष पर नहीं पहुंचना चाहिए।

लक्षण विश्लेषण: सिस्टम के लक्षणों को देखा जाना चाहिए या विश्लेषण किया जाना चाहिए कि क्या समस्या सिस्टम के किसी भी हिस्से से हो सकती है। समस्या सॉफ्टवेयर की मेमोरी डिवाइस या बिजली आपूर्ति से सिस्टम विश्लेषण करके हार्डवेयर है, हम मरम्मत की प्रक्रिया शुरू कर सकते हैं सही खंड में।

दोष निदान: दोष के कारण और विभाग का पता एक बार के लक्षण अवलोकन से लगाया जा सकता है। दोषपूर्ण उपकरण का पता लगाने और मरम्मत की प्रक्रिया शुरू होनी चाहिए। गलती का निदान करते समय किसी भी तरह से किसी भी तरह से निपटने में कोई दिक्कत नहीं होनी चाहिए।


दोष सुधार: निदान के बाद, यदि आप दोषपूर्ण डिवाइस को बदल रहे हैं, तो डिवाइस के मिलान को ध्यान में रखा जाना चाहिए और नए डिवाइस के मूल्य और क्षमता को जोड़ा जाना चाहिए। कंप्यूटर एक ऐसा उपकरण है जो न केवल नए डिवाइड को बदलकर काम करता है, बल्कि इसे बायोस सॉफ्टवेयर द्वारा कॉन्फ़िगर करने की भी आवश्यकता होती है। डिवाइस को बदलने के बाद, इन आवश्यकताओं को भी पूरा करें।




For More Detail:- Click Here For Videos

No comments:

Post a Comment

Post Top Ad

Your Ad Spot

Pages